Guide :Home Security : Fireproof Safe

My safe has 9-volt battery when I put in code the proceed light

Flashes and red error is burning.If i change battery will I have to reprogram as I have misplace book.

Research, Knowledge and Information :


Opening a Sentry Safe with a Rubber Mallet, some WD-40 and a ...


Opening a Sentry Safe with a Rubber Mallet, ... The plastic battery holder has a connection for a 9 volt battery ... So I stuck in a 9V battery, put in the code and ...
Read More At : idoneitmyself.com...

Troubleshooting Tips | Winchester Safes


Click here for common troubleshooting tips ... battery is installed (9-volt ALKALINE ... longer during safe lock operation. I enter my code in the electronic ...
Read More At : winchestersafes.com...

Fire-Resistant Executive Gun Safe Owner’s Manual Troubleshooting


battery tray and insert a 9 volt alkaline battery into the battery tray. ... The wrong code has been entered into the safe. ... to have a red light illuminate the
Read More At : www.sentrysafe.com...

68790-CannonSafe Text.qxp 2/3/09 8:27 AM Page 1 DO NOT LOCK ...


or safes which have been misused, neglected, or put ... • Attach new 9-Volt Alkaline Battery to ... before you start using the safe. 68790-CannonSafe_Text.qxp 2/3 ...
Read More At : www.maximumsecurity.com...

Operating Instructions Lock Instructions Warranty Extended ...


Operating Instructions Lock Instructions Warranty ... Do Install an Energizer Alkaline 9 Volt battery ... gun safe. It is a simple process but must be executed ...
Read More At : www.gunsafes.com...

Q & A: Powering a light bulb with a battery | Department of ...


Q & A: Powering a light bulb with a battery ... because it can still put out some colors of light ... So this naive model would predict that the 9 Volt battery would ...
Read More At : van.physics.illinois.edu...

Frequently Asked Questions | Winchester Safes


If the correct battery is installed (9-volt ALKALINE ... and answers to many frequently asked questions. ... code to the lock inside the safe. Your code is stored in ...
Read More At : winchestersafes.com...

Light bulb, battery, and two wires - YouTube


Jul 12, 2011 · How do you light a light bulb with some bare copper ... Light bulb, battery, and two wires ... run a 220 Volt light bulb on a 9 Volt battery - win or fail?

My Sentry safe won't open with the combination


My Sentry safe won't open with the combination ... Does the light turn green to proceed? ... Do you have the original code that came with the safe? Have you ever ...
Read More At : www.justanswer.com...

Suggested Questions And Answer :


Can't get it open after keying in code. error


Http://www.sentrysafe.com the instructions are located link above. mj
Read More At : Fireproof Safe...

My safe has 9-volt battery when I put in code the proceed light


Hi,Check Sentry Safe Support for manual and programing.
Read More At : Fireproof Safe...

Sentry safe reset instructions


You can get help here, but you will need to prove ownership... http://www.sentrysafe.com/CustomerCare/
Read More At : Home Security...

We have a Sentry safe model number SC 3877. We just changed the batteries. We are imutting the correct code, the light turns green but does not give the 1 beep and we cannot open the safe. If we put in the incorrect code the red LED light flashes and gives 3 beeps, but the green one does not beep. The key lock is out. Help!!


Http://callitout.com/quotes/index.php/kick-it-to-the-curb/55/sentry-fire-safe-wont-open-its-broken/Its the most reazonable answer and it worked!!!!!!! dial the code and tap on the handle so it would get lose
Read More At : Fireproof Safe...

Error light comes on when keying combination code


Try new batterys ,also sometimes if too full ,you will have to hit it hard to get the stuff off the lock bars that keep them from moving .
Read More At : Fireproof Safe...

Sentry Model 1610 Won't Open


Hi, here is the customer service phone number for you. I am sure they will be able to help you. 800-828-1438
Read More At : Fireproof Safe...

Green proceed light goes on but door does not depress lock


I have a different model but I had the same problem. Called customer service and they had me push up on the handle and enter the code. That didn't work but then they had me tap the safe with a rubber mallet 5 times above the panel and 5 times to the right of the panel. That worked for me. Hope one of those works.
Read More At : Fireproof Safe...

Low batteries in my safemark safe- how do i open?


E-bar is not a battery problem, it means the door lock is jammed, either use a rubber malet or your balled up fist and after inputting the code to unlock hit the door of the safe all around the key pad as hard a you can, your will hear the rods moving and unlocking the door. Hope this helps. I know it works I do this at the hotel I work in.
Read More At : Safe International...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || home-security-101.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0647 seconds